欢迎来到恒丰友电气中文官网---智能电气全球服务提供商·让生活更美好！
Writer： 恒丰友电气 Time：2021-09-09 浏览量：次
| No. | 中文名称 | Name |
|---|---|---|
| ANSI C12.9-2005 | 变压器额定仪表用测试开关 | Test Switches for Transformer-Rated Meters |
| ANSI C57.12.10-1998 | 电压不大于230千伏且容量为833/958至8333/10417千伏安单相及750/862至60000/80000/100000千伏安三相的变压 | Transformers 230 kV and Below, 833/958 through 8333/10 417 kVA Single Phase, and 750/862 through 60 000/80 000/100 000 kVA Three Phase, Requirements for |
| ANSI C57.12.20-1997 | 变压器.不大于500kVA的架空配电变压器:高压不大于34500伏、低压不大于 7970/13800Y伏 | Transformers - Overhead-Type Distribution Transformers, 500 kVA and Smaller: High Voltage, 34 500 Volts and Below; Low Voltage, 7970/13 800Y Volts and Below |
| ANSI C57.12.24-2000 | 变压器.不大于2500kVA的地下型三相配电变压器:高压不大于34500Y接地/19920伏、低压不大于480伏.要求 | Transformers - Underground-Type Three-Phase Distribution Transformers, 2500 kVA and Smaller: High Voltage 34 500 Grd Y/19 920 Volts and Below; Low Voltage, 480 Volts and Below - Requirements |
| ANSI C57.12.50-1981 | 高压601至34500伏,低压120至600伏,容量单相1至500千伏安和三相15至500千伏安,通风干式配电变压器的要求 | Ventilated Dry-Type Distribution Transformers, 1 to 500 kVA, Single-Phase and 15 to 500 kVA, Three-Phase, with High-Voltage 601 to 34 500 Volts, Low-Voltage 120 to 600 Volts, Requirements for; Correction June 1982 |
| ANSI C57.12.51-1981 | 三相，高压601至34500伏,低压208Y/120至4160伏容量不小于501千伏安,通风干式电力变压器的要求 | Requirements for Ventilated Dry-Type Power Transformers, 501 kVA and Larger, Three-Phase, with High-Voltage 601 to 34 500 Volts, Low-Voltage 208Y/120 to 4160 Volts |
| ANSI C57.12.52-1981 | 三相，高压:601至34500伏，低压:208Y/120至4160伏,容量不小于501千伏安,密封干式电力变压器的要求 | Requirements for Sealed Dry-Type Power Transformers, 501 kVA and Larger, Three-Phase, with High-Voltage 601 to 34 500 Volts, Low-Voltage 208Y/120 to 4160 Volts |
| ANSI C57.12.55-1987 | 变压器.包括成套变电所在内的成套设备用干式变压器.一致性标准 | Transformers - Dry-Type Transformers Used in Unit Installations, Including Unit Substations - Conformance Standard |
| ANSI C82.7-1983 | 水银灯变压器.恒定电流(系列)供电型 | Mercury Lamp Transformers - Constant-Current (Series) Supply Type |
| ANSI C82.8-1988 | 灯变压器.白炽灯变压器.恒定电流(系列)供电型 | Lamp Transformers - Incandescent Filament Lamp Transformers - Constant-Current (Series) Supply Type |
| ANSI C82.9-1996 | 高亮度放电和低压钠灯、镇流器和变压器.定义 | High-Intensity-Discharge and Low-Pressure Sodium Lamps, Ballasts and Transformers - Definitions |
| ANSI C82.9b-1998 | 电灯镇流器.高强度放电和低压钠灯镇流器和变压器的定义 | Electric Lamp Ballasts - High-Intensity-Discharge and Low-Pressure Sodium Lamps, Ballasts and Transformers - Definitions |
| ANSI/ASTM A1009-2000 | 高频(10KHz-1MHz)电源变压器和过滤电感器软磁化锰锌铁芯材料规范 | Specification for Soft Magnetic MnZn Ferrite Core Materials for High Frequency (10KHz to 1MHz) Power Transformer and Filter Inductor Applications |
| ANSI/IEEE 111-2000 | 宽带（大于10倍频程）变压器标准 | Standard for Wide Band (Greater than 1 Decade) Transformers |
| ANSI/IEEE 1538-2000 | 充液变压器的最大绕组温升的测定指南 | Guide for Determination of Maximum Winding Temperature Rise in Liquid Filled Transformers |
| ANSI/IEEE 295-1969 | 电子设备电力变压器 | Electronics Power Transformers |
| ANSI/IEEE 388-1992 | 电子功率变换设备中的变压器和感应线圈 | Transformers and Inductors in Electronic Power Conversion Equipment |
| ANSI/IEEE 389-1996 | 测试电子电路变压器和感应器的推荐实施规程 | Recommended Practice for Testing Electronic Transformers and Inductors |
| ANSI/IEEE 436-1991 | 电子电路变压器产生电晕(局部放电)的测量指南 | Guide for Making Corona (Partial Discharge) Measurements on Electronics Transformers |
| ANSI/IEEE 62-1995 | 电力设备的诊断现场试验指南.第1部分:充油电力变压器、调节器和电抗器 | Guide for Diagnostic Field Testing of Electric Power Apparatus - Part 1: Oil Filled Power Transformers, Regulators, and Reactors |
| ANSI/IEEE 638-1992 | 核电站用IE级变压器的合格鉴定 | Standard for Qualification of Class 1E Transformers for Nuclear Power Generating Stations |
| ANSI/IEEE C37.108-2002 | 保护网络变压器指南 | Guide for the Protection of Network Transformers |
| ANSI/IEEE C37.91-2000 | 电力变压器的保护继电器应用指南 | Protective Relay Applications to Power Transformers, Guide for |
| ANSI/IEEE C57.100-1999 | 油浸式配电变压器热评定试验规程 | Distribution Transformers, Test Procedure for Thermal Evaluation of Oil-Immersed |
| ANSI/IEEE C57.105-1992 | 三相配电系统变压器连接申请 | Application of Transformer Connections in Three-Phase Distribution Systems |
| ANSI/IEEE C57.109-1993 | 液浸式变压器穿越故障电流持续时间的指南 | Guide for Liquid-Immersed Transformer Through-Fault Current Duration |
| ANSI/IEEE C57.110-2004 | 施加非正弦负载电流时变压器性能确定的推荐实施规程 | Recommended Practice for Establishing Transformer Capability When Supplying Nonsinusoidal Load Currents |
| ANSI/IEEE C57.111-1995 | 硅绝缘液体验收指南和在变压器中的维护 | Guide for Acceptance of Silicone Insulating Fluid and Its Maintenance in Transformers |
| ANSI/IEEE C57.113-2002 | 充液电力变压器和并联电抗器的局部放电测量指南 | Guide for Partial Discharge Measurement in Liquid-Filled Power Transformers and Shunt Reactors |
| ANSI/IEEE C57.116-1990 | 直接连于发电机的变压器指南 | Guide for Transformers Directly Connected to Generators |
| ANSI/IEEE C57.117-1986 | 公用电力系统的电力变压器和并联电抗器失效数据报告指南 | Reporting Failure Data for Power Transformers and Shunt Reactors on Electric Utility Power Systems, Guide for |
| ANSI/IEEE C57.119-2002 | 超出铭牌额定值的负荷下进行油浸电力变压器升温试验的推荐惯例 | Recommended Practice for Performing Temperature Rise Tests on Oil Immersed Power Transformers at Loads Beyond Nameplate Ratings |
| ANSI/IEEE C57.12.01-2005 | 包括固体浇铸和/或树脂密封绕组的干式配电和电力变压器的标准.一般要求 | Standard General Requirements for Dry-Type Distribution and Power Transformers Including Those with Solid-Cast and/or Resin Encapsulated Windings |
| ANSI/IEEE C57.12.20-2005 | 500 kVA及更小的顶置式配电变压器的标准:高压34500V及以下、低压7970/13800Y伏特及以下 | Standard for Overhead Type Distribution Transformers, 500 kVA and Smaller: High Voltage, 34 500 Volts and Below; Low Voltage, 7970/13 800Y Volts and Below |
| ANSI/IEEE C57.12.23-2002 | 变压器.带可分离绝缘高压连接器的地下型、自冷式单相配电变压器.高压(24940GrdV/14400V及以下)和低压(240/1 | Transformers - Underground-Type, Self-Cooled, Single-Phase Distribution Transformers with Separable, Insulated, High-Voltage Connectors; High Voltage (24 940 GrdY/14 400 V and Below) and Low Voltage (240/120 V, 167 kVA and Smaller) |
| ANSI/IEEE C57.12.34-2004 | 底座安装的隔室型自冷式三相配电变压器2500 kVA及更小:高压34500 GrdY/19920伏及以下、低压480伏及以下的要 | Standard Requirements for Pad-Mounted, Compartmental-Type, Self-Cooled, Three-Phase Distribution Transformers, 2500 kVA and Smaller: High-Voltage, 34 500 GrdY/19 920 Volts and Below; Low Voltage, 480 Volts and Below |
| ANSI/IEEE C57.12.35-1996 | 配电变压器的标准条形编码 | Standard Bar Coding for Distribution Transformers |
| ANSI/IEEE C57.12.56-1994 | 通风干燥型电力和配电变压器绝缘系统热评价的试验程序 | Test Procedure for Thermal Evaluation of Insulation Systems for Ventilated Dry-Type Power and Distribution Transformers (reinstatement of administratively withdrawn standard) |
| ANSI/IEEE C57.12.58-1991 | 干式变压器线圈瞬态电压分析指南 | Guide for Conducting a Transient Voltage Analysis of a Dry Type Transformer Coil |
| ANSI/IEEE C57.12.59-2002 | 干式变压器全故障电流持续时间指南 | Guide for Dry-Type Transformer Through-Fault Current Duration |
| ANSI/IEEE C57.12.60-1998 | 固体浇铸和树脂密封的电力和配电变压器绝缘系统热评定试验程序指南 | Guide for Test Procedures for Thermal Evaluation of Insulation Systems for Solid Cast and Resin-Encapsulated Power and Distribution Transformers |
| ANSI/IEEE C57.12.70-2000 | 输电及电力变压器用终端标志和连接标准 | Standard Terminal Markings and Connections for Distribution and Power Transformers |
| ANSI/IEEE C57.12.80-2002 | 电力分配变压器术语 | Terminology for Power and Distribution Transformers |
| ANSI/IEEE C57.12.90-1999 | 油浸式配电、电力和调压变压器的试验规程及电力和配电变压器短路试验指南 | Test Code for Liquid-Immersed Distribution, Power and Regulating Transformers and Guide for Short-Circuit Testing of Distribution and Power Transformers |
| ANSI/IEEE C57.120-1992 | 电力变压器和电抗器的损耗评价指南 | Loss Evaluation Guide for Power Transformers and Reactors |
| ANSI/IEEE C57.123-2002 | 变压器损失测量指南 | Guide for Transformer Loss Measurement |
| ANSI/IEEE C57.124-1991 | 干式变压器表观电荷部分放电和测量的检测 | Detection of Partial Discharges and the Measurement of Apparent Charge in Dry Type Transformers |
| ANSI/IEEE C57.125-2005 | 电力变压器和分流扼流器故障研究、记录和分析指南 | Guide for Failure Investigation, Documentation, and Analysis for Power Transformers and Shunt Reactors |
| ANSI/IEEE C57.13-2003 | 仪表用变压器标准要求 | Standard Requirements for Instrument Transformers |
| ANSI/IEEE C57.13.1-1981 | 继电器用的电流变压器现场测试指南 | Field Testing of Relaying Current Transformers |
| ANSI/IEEE C57.13.2-2005 | 仪表用变压器标准合格测试程序 | Standard Conformance Test Procedure for Instrument Transformers |
| ANSI/IEEE C57.13.3-2005 | 仪表用变压器次级线圈电路和外壳接地指南 | Guide for Grounding of Instrument Transformer Secondary Circuits and Cases |
| ANSI/IEEE C57.13.6-2005 | 高精度仪表变压器标准 | Standard for High Accuracy Instrument Transformers |
| ANSI/IEEE C57.134-2000 | 干式变压器热斑温度测定指南 | Guide for Determination of Hottest Spot Temperature in Dry Type Transformers |
| ANSI/IEEE C57.135-2001 | 移相变压器的应用、规范和测试指南 | Guide for the Application, Specification and Testing of Phase-Shifting Transformers |
| ANSI/IEEE C57.136-2000 | 额定功率大于500kVA的油浸式电力变压器和并联电抗器的声级抑制和测定指南 | Guide for Sound Level Abatement & Determination for Liquid-Immersed Power Transformers & Shunt Reactors Rated Over 500 kVA |
| ANSI/IEEE C57.138 (R200x)-1998 | 配电变压器常规脉冲试验的推荐实施规程 | Recommended Practice for Routine Impulse Test for Distribution Transformers |
| ANSI/IEEE C57.138-1998 | 配电变压器常规脉冲试验推荐惯例 | Recommended Practice for Routine Impulse Test for Distribution Transformers |
| ANSI/IEEE C57.144-2004 | 变压器标准的米制转换指南 | Guide for Metric Conversion of Transformer Standards |
| ANSI/IEEE C57.146-2005 | 硅树脂浸变压器产生气体的说明指南 | Guide for the Interpretation of Gases Generated in Silicone-Immersed Transformers |
| ANSI/IEEE C57.18.10-1998 | 半导体电力整流变压器要求和标准实施规程 | Standard Practices and Requirements for Semiconductor Power Rectifier Transformers |
| ANSI/IEEE C57.91-2004 | 矿物油浸式变压器的加载指南 | Guide for Loading Mineral-Oil-Immersed Transformers |
| ANSI/IEEE C57.93-1995 | 液浸式电力变压器的安装指南 | Guide for Installation of Liquid Immersed Power Transformers |
| ANSI/IEEE C57.94-2000 | 干式通用配电及电力变压器的安装、应用、操作和维护的推荐规程 | Recommended Practice for Installation, Application, Operation, and Maintenance of Dry-Type General-Purpose Distribution and Power Transformers |
| ANSI/IEEE C57.96-1999 | 负载干式配电和电源变压器指南 | Distribution and Power Transformers, Guide for Loading Dry-Type (appendix to ANSI C57.12 standards) |
| ANSI/IEEE C57.98-1993 | 变压器脉冲试验指南 | Impulse Tests, Guide for Transformer (appendix to ANSI/IEEE C57.12.90) |
| ANSI/NECA 409-2002 | 干式变压器的安装和维护的推荐规程 | Recommended Practice for Installing and Maintaining Dry-Type Transformers |
| ANSI/NECA 410-2005 | 充液变压器安装和维修标准 | Standard for Installing and Maintaining Liquid-Filled Transformers |
| ANSI/NETA MTS7.2.1-2001 | 干式变压器NETA维护测试规范:气冷600V及以下.小型(167kV单相,500kVA三相及更小)和气冷600V及以下.大型(大于 | NETA Maintenance Testing Specifications for Dry-Type Transformers: Air-Cooled, 600 Volts and Below - Small (167 kV Single-Phase, 500 kVA Three-Phase, and Smaller) and Air-Cooled, All Above 600 Volts and 600 Volts and Below - Large (Greater than 167 kV Single-Phase and 500 kVA Three-Phase) |
| ANSI/NETA MTS7.2.2-2001 | 充液变压器维护测试规范 | Maintenance Testing Specifications for Liquid-Filled Transformers |
| ANSI/SCTE 68-2003 | 无源电压降:匹配变压器75ohm到300ohm | Drop Passives: Matching Transformers 75 ohm to 300 ohm |
| ANSI/UL 1310-2005 | 直接插入式变压器设备 | Direct Plug-in Transformer Units |
| ANSI/UL 1561-2005 | 干式通用和电力变压器 | Dry-Type General Purpose and Power Transformers |
| ANSI/UL 506-2005 | 专用变压器 | Specialty Transformers |
| ANSI/UL 551-1993 | 变压器型弧焊机 | Transformer-Type Arc-Welding Machines |
| ANSI/UL 697-2004 | 玩具变压器 | Toy Transformers |
| ASTM A 1009-2005 | 高频(10kHz-1MHz)电力变压器和滤波感应器用软磁性MnZn铁芯材料标准规范 | Standard Specification for Soft Magnetic MnZn Ferrite Core Materials for High Frequency (10 kHz-1 MHz) Power Transformer and Filter Inductor Applications |
| ASTM D 2759-2000 | 在正压力下从变压器中抽取气体样品的标准实施规程 | Standard Practice for Sampling Gas from a Transformer Under Positive Pressure |
| ASTM D 3305-1994 | 从变压器中抽取小体积气体样品的标准实施规程 | Standard Practice for Sampling Small Gas Volume in a Transformer |
| UL 1411-1998 | 音频、无线电和电视类装置用变压器与电机变压器 | (Transformers and motor transformers for use in audio-, radio-, and television-type appliances ) |
| UL 1561-1999 | 干式通用电力变压器 | (Dry-type general purpose power transformers ) |
| UL 1562-1999 | 干式600V以上变压器、配电系统 | (Transformers, distribution, dry-type over 600 volts ) |
| UL 1585-1998 | 2类和3类变压器 | (Class 2 and class 3 transformers ) |
| UL 1876-2001 | 电子设备中隔离和反馈信号用变压器 | (Isolating signal and feedback transformers for use in electronic equipment ) |
| UL 2161-1996 | 氖变压器和电力电源 | (Neon transformers and power supplies ) |
| UL 551-1994 | 变压器型弧焊机 | (Transformer-type arc-welding machines ) |
| UL 697-1998 | 玩具用变压器 | (Toy transformers ) |
| No. | Name |
Name |
青岛恒丰友电气隶属于恒丰帅集团，是一家专业从事电力配电产品生产制造销售的专业化电气公司，主要从事配电变压器、整流变压器、电炉变压器等生产及全球化销售。恒丰友电气具备多年为欧美、中东客户提供OEM/ODM服务的经验。同时可提供变压器铁芯、变压器线圈、变压器外壳的定制生产。如果您有电力变压器需求，非常期待与您的合作。https://www.hengfengyou.com ；info@hengfengyou.com；WhatsApp：+8615853252696
© 2021 Copyright By Hengfengyou 版权所有
QQ客服